Plantronics Savi 700 Series (W710, W720, W730, W740): Use with a Bluetooth mobile cell phone

W730 Over-the-Ear Wireless HeadsetFor Savi 700 series model information:

Plantronics W710 – Single-Ear Wireless Headset

Plantronics W720 – Dual-Ear Wireless Headset

Plantronics W730 – Over-the-Ear Wireless Headset

Plantronics W740 – Convertible Wireless Headset

Your Bluetooth mobile or smart phone can be paired to a Plantronics 700 Series (710, 720, 730, 740) wireless headset system base in the office so that you can use the same wireless headset for all of your in-office mobile calls as well.

Bluetooth Pairing and Auto Connect Feature:

Once you have paired and connected your mobile phone to the 700 Series (710, 720, 730, 740) base, the base will automatically connect to you mobile phone when you are in range of your headset base.  You can manually disconnect your mobile phone from the base by short pressing the base Bluetooth pairing button when it is solid blue.  However if you do this, you must manually re-establish a connection with your mobile phone by pressing the base Bluetooth button again before the auto connection feature will resume.

Auto Connect to Mobile Phone:

This feature automatically establishes a Bluetooth link to the mobile phone whenever the mobile phone is within range.  See the following setting for an optional restriction on this function.

Stop Auto Connect to Mobile When Headset Is Docked

If this feature is enabled, the base will not automatically establish a Bluetooth connection to your mobile phone when the headset is docked.  Upon undocking the headset, the base will automatically establish a Bluetooth connection if “auto connect” to mobile phone” is selected.

Placing a mobile phone call:

  • While wearing your headset, short press the base mobile phone button.  If you place the mobile phone call without pressing the base mobile button first, the audio will stay on the mobile phone.  If you would like to transfer the audio to your headset, short press the mobile base button.
  • Dial a call from your mobile phone.
  • End the call by pressing the headset call control button.

Hands-free dialing:  To enable hands-free dialing, install the Plantronics software.  Once installed, go to Start > Programs > Plantronics > Plantronics Control Panel > Device Settings > Base and activate “Initiate Mobile voice commands”.  For hands-free dialing, initiate the mobile call from the base by pressing the base mobile phone button.  Your mobile phone will prompt you for voice commands.  Alternatively, you can dial a number from your mobile phone and then press the base mobile phone button to move the audio to the headset.

Answer a Call with Your Mobile Phone:

If you answer an incoming mobile call using the answer button on the mobile phone, the audio will remain in the phone.  If you answer an incoming call using the headset or base, the audio will be in the headset.

Reject a Mobile Call:

When you receive an incoming mobile phone call, the mobile button on the base will flash green.  To reject the call, hold the base mobile phone button down for 3 seconds.

Mobile Phone and Headset Audio:

If you answer an incoming mobile call using the answer button on the phone, the audio will remain in the cell phone.  If you answer an incoming call using the headset or base, the audio will be in the headset.  If the mobile phone audio is in the mobile phone, you can move the audio to the headset by short pressing the base mobile button when the LED is off.  To move mobile phone audio from the headset back to the phone, hold the base mobile button for 3 seconds until the solid green LED turns off.  The audio will be back to the mobile phone.

Bluetooth Enabled:

This feature disables/enables use of the Bluetooth interface to the mobile phone.  The Bluetooth interface to the mobile phone can also be disabled / enabled manually by pressing the subscription and base mobile phone button until the base mobile phone LED flashes.  When the base mobile phone button LED flashes red four times, Bluetooth is disabled and when it flashes green four times, it is enabled.

Initiate Mobile Voice Commands:

This feature enables/disables mobile phone voice commands for hands-free dialing with yourmobile phone.  When this is enabled, you will be prompted for voice commands by your mobilephone when a call is initiated with the base mobile button.  This feature requires mobile phone support for voice commands.

Leave a Reply

Your email address will not be published. Required fields are marked *